He’s 81, not 88.

I run a development department, and nobody who reports to me comes to the office. We have been 100% remote since 2020… much to the chagrin of HR. Others in IT come in, but no developers. I see no reason to change it either. I question why I even come in most days.

Without looking it up, I don’t know how many people I’ve interviewed over the last 4 years, but there’s been a few. I’ve only had one person who indicated he wanted to be in an office. Every other person wants fully remote. The most common comment I’ve heard from people is saying they will settle for hybrid if full-remote isn’t available.

There’s some value to having people work together in-person, but I’d rather give my teams the flexibility to choose for themselves rather than force it.

Just another BS article designed to get clicks.

7/144 = 4.9% With the information presented and using the same jump-to-conclusion analysis, energy drinks reduced the likelihood of a cardiac arrest by over 95%.

I winder how many of the 144 had brown hair. Let’s guess 30%. The article could read, “People with brown hair have a 30% likelihood of cardiac arest. Why hair dye saves lives?”

Shellac is not the same as oil based. Oil based is made from, well, oil. Shelllac is made by crushing the shells of the lac bug. It is an insect that is cultivated specifically for the purpose. Shellac is typically used as a final coat for protection. Shellac primer is basically that mixed with a white pigment. It is great for sealing. Fairly pricy though.

I will echo the Bondo route that others suggested. The big box hardware stores sell quart cans of general purpose Bondo in the paint aisle.

Cut out the vaneer over the bad area with a razor blade or box cutter.

Sand with 80 or 120 grit to remove any loose bits of the board. The particle board will crumble a little, but it will be fine. Just dont go overboard. Vacuum it to remove most dust.

Using a flexible putty knife, get one to two globs of Bondo on a clean piece of cardboard. Don’t do too much as you will have about 5 minutes of working time once the hardener is added. Follow the instructions on how much hardener to add, you wont need much. Fold the hardener into the Bondo with the putty knife until it is a uniform color.

Spread the bondo over the area you cut out. Try to get it smooth, but dont overwork it. It doesn’t have to be perfect.

Using 60 or 80 grit paper, sand it as it starts to dry. If it is gumming up the paper, it is still too wet to sand, give it another minute or two and try again. You are shaping it with this step. If you let it completely dry, it is hard as a rock and more difficult to sand.

Once it is in a good shape, switch to the next step up for sanding and repeat (60 to 80 to 120 to 180 to 220). Do not skip gits or you will just make work for yourself. You can probably stop at 180, but since it is next to vaneer, i’d go to 220. Again, if it is gumming the paper, wait a few minutes. Once you are at 220, use it to sand the entire cabinet to rough up the surface and accept primer better.

Once sanded, wipe the entire cabinet down with a tac cloth. I also recommend wiping the cabinets with a wax and greese remover so everything will stick better.

Now it is time for primer and paint. For a smooth finish, use a good quality foam mini-roller and foam brush for tighter areas.

Prime the cabinet using any water-based primer; killz is pretty good. They make an oil based that would be better, but will smell up your whole house, so I don’t recommend it unless you have excellent ventilation.

Lightly sand the peimer once it is fully dried with 220. If any spot is too light, do a second coat. Wipe up the dust.

Paint with an alkyd paint. Do at least 2 coats.

Not necessary, but if you want extra protection, you could use a foam brush (not a roller here) and do 3 to 4 coats of a water-based polyurethane on top of the paint. It might be overkill for what you want though.

This might seem like a lot, but you will have a great finish when done. Also, fair warning, Bondo has a strong smell. Open a window.